|
Ningbo Sanboo Auto Parts International Trade Co., Ltd.
|
Product (398)
-
Automatic Transmission Oil Pumps
(2)
-
Automatic Transmission Solenoid Valves
(2)
-
Automatic Transmission Parts
(247)
-
Rebuilt Automatic Transmissions
(27)
-
Other Auto Parts
(115)
- Others (5)
Special Groups (108)
Sanboo Automatic Transmission Repair Centers (1)
charity (1)
SALES TEAM (1)
Common fault of Jetta 01M auto transmission (1)
introduce some principle of transmission (1)
Problem solving (2)
Excelle 4HP16 (5)
Knowledge (30)
Certificates (5)
Credit Report
Products Index
Company Info
Ningbo Sanboo Auto Parts International Trade Co., Ltd. [China (Mainland)]
Business Type:Manufacturer, Trading Company
City: Ningbo
Province/State: Zhejiang
Country/Region: China (Mainland)
|
sanboo:
|
|
Jack Weng:
|
Knowledge
Start Control
This system is equipped with automatic start device (One-touch effect), ME injection system when the computer receives the start signal 50, ME injection computer seized two feet to ME computer D3 grounding, so suck platinum, starter operation
If at this time 50 signal interruption (ie the ignition switch to relax, not in the starting position), starter motor continues to run until the engine is running,
ME computer will cut the D3 Ground, starter stopped, or the ignition switch off.
If at this time 50 signal interruption (ie the ignition switch to relax, not in the starting position), starter motor continues to run until the engine is running,
ME computer will cut the D3 Ground, starter stopped, or the ignition switch off.
Hydraulic control and shift solenoid valve
The first 38pin PC power supply to all of hydraulic solenoid valves, for the first 37,36,14,15,16,17 foot hydraulic solenoid valves, hydraulic solenoid valves for each of the following is the role of each gear diagram: 722.6 automatically checked by the Transmission shift lever position is now sending computer is in the P / N position (inside the gearbox P / N start control reed switch), this P / N position to the ME computer from the automatic gearbox injection system computer 7 feet, then ME computer and then spray solenoid starter relay K2 by the 1st plug first k40 / 4 integrated relays within
14 feet to control the 1-2 / 4-5 gear shift solenoid valve (when the shift solenoid valve is turned on)
15 feeet to control the 3-4 gear shift solenoid valve(when the shift soleboid valve is turned on)
16 feet to control the 2-3 gear shift solenoid valve(when the shift solenoid valve is turned on)
17 feet of the lockup clutch solenoid valve( when the vehicle speed of 90-100km, at light loads, hydraulic solenoid valve engagement, so that the torque converter lockup clutch is engaged, the pump wheel and turbine combined into one, so that the torque the difference is zero, reducing power loss)
36 feet to control main hydrualic solenoid valve(according to road conditions and engine load conditions,to adjust the gearbox oil,large load.Hydraulic high-speed,low oil pressure)
37 feet to control shift hydraulic solenoid valve(for adjusting the pressure of shift work,so that shift more smoothly)
Input/output speed sensor
Computer No. 13 foot speed sensor Hall sensor power supply, 33 feet for the sensor Ground, No. 35 feet for the input shaft speed signal output, No. 12 feet for the output shaft speed signal output, they are a square wave output. Used to detect the shift, adjust the oil pressure.
Temperature sensor/P/N syarter control switch
34 feet for P / N starter control switch magnetic reed switch opens in P / N, the signal is sent to the ME do start signal, the shift lever into R, D
When blocked, the first 34 feet and can detect automatic transmission oil temperature.
When blocked, the first 34 feet and can detect automatic transmission oil temperature.
